Machine Parts For Reuse Newsgroup Discussion Forum > Small Size Parts
> Non functional
> Electronic
> Milaukee
> Nxp LPC1300 board evaluation jtag arm cortex-M3 usb
Nxp LPC1300 board evaluation jtag arm cortex-M3 usb
The NXP LPC1300 ARM-CM3 Board is a brand new, cost-effective but high-performance evaluation tool of the ARM Cortex-M3 based LPC1300 controller family from NXP, allowing you to create and test working programs for this advanced architecture.
The board has a wide range of interfaces making it a great starting point for your next Cortex-M3 project.
* 72MHz LPC1300 ARM Cortex -M3 processor
* On-Chip Memory: 32KB Flash & 8KB RAM
* Plenty of software examples
1-14.jpg picture by sylvia1024_photo
You can use the Cortex-M3 based LPC1300 Evaluation Board to generate and test application programs for the NXP LPC13xx microcontroller family. With this hands-on process, you can determine the hardware and software requirements for current and future product development.
The LPC1300 Evaluation Board introduces the new LPC1300 family of ARM Cortex-M3 processor-based devices, allowing you to create and test working programs for this advanced architecture.
* Processor: NXP LPC1343FBD48, based on ARM Cortex-M3 Core, 72MHz
* External Memory: 8KB EEPROM accessible via I2C bus
* 2 x Push buttons (Reset, BOOT)
* Board Size: 110mm x 140mm (4.33" x 5.5")
* Supply Voltage: 5 Volts DC (provided by the USB bus of a PC)
* Supply Current: 180mA typical, 200mA maximum
To compile, link and run applications on the LPC1300 Evaluation Board, you must install these products:
* The RealView MDK-ARM which includes the Vision Debugger and provides several example programs for the LPC1300 Board.
* The example programs and project files for the board are accompanied with CDROM, developed by Embest.
Embest Provides plenty of software examples for this evaluation board, all in source code. These software examples can be debugged under the popular Keil MDK (Microcontroller Development Kit) environments, making practical use of the board's peripherals.
There are plenty of documentations and materials in the CD-ROM of this NXP LPC1300 Cortex-M3 Board, such as user s manual, datasheets, software, example programs, and so on. If you need these materials, please feel free to contact us.
17-9.jpg picture by sylvia1024_photo 18-8.gif picture by sylvia1024_photo 2-13.jpg picture by sylvia1024_photo 19-10.jpg picture by sylvia1024_photo
The NXP LPC1300 series is based on the Cortex-M3 Rev2 core and is designed for embedded 16 and 32-bit applications. The new MCUs operate at 70MHz and consume about 200 A per MHz.
12-14.jpg picture by sylvia1024_photo
LPC1300 Microcontrollers Features
* ARM Cortex-M3 processor running at up to 70MHz
* Up to 32KB flash, up to 8KB SRAM
* USB 2.0 full-speed device controller with on-chip PHY (LPC134x)
* UART, SPI controller, I2C-bus interface
* 4 timers plus programmable WDT with lockout feature
* Integrated power management with deep-sleep modes
* Integrated clock generation
The new LPC1311/13/42/43 microcontrollers feature up to 32kB of flash memory, 8kB of SRAM memory, low-cost USB, up to 42 general purpose I/O pins, and built-in Nested Vectored Interrupt Controller (NVIC). The LPC1300 enables in-system programming and in-application programming via on-chip bootloader software and offer a range of serial interfaces including high speed USB 2.0 with on-chip PHY, UART, SSP/SPI controller, and I2C-bus interface. For ease of use, USB Mass Storage and HID class drivers are included on-chip enabling USB communication to be set up in minutes. These drivers are incorporated in ROM, leaving 100% of the user Flash space for the application.
22-10.jpg picture by sylvia1024_photo
More Info: The NXP LPC1300 series Microcontrollers
Main Board, based on LPC1343 processor
Connect the COM port to Host PC. 9-pin male to 9-pin female, no longer than 10ft/3m, wired one-to-one
To supply power to the board or for downloading and programming
Convert the signal between the 20pins and 10pins interfaces
Convert the signal between the DB9 and DIP 10pins interfaces
13-10.jpg picture by sylvia1024_photo
14-10.jpg picture by sylvia1024_photo
15-9.jpg picture by sylvia1024_photo
Total weight of each standard package (kg): kg
01-Documents - user manual, data sheets and the other development documents.
02-Images - image files for this product.
03-Software - software programs for this product.
04-Tools - the utilities tools and software
16-9.jpg picture by sylvia1024_photo
Please contact us for higher volumes
